Model NITI Aayog, 24-27 Dec, online. Write an original white paper.

How Does a Touchscreen Know Where You Touch? | How It Works

12 min read

On this page

What is the short answer?

A touchscreen has thin sensing layers over its display. A touch changes something electrical in them, and a chip called a controller turns that change into a position: how far across and how far down.

Definition: A touchscreen is a display that is also an input device. Transparent layers over the picture, or sensors around its edge, sense where a finger or stylus touches and report it as a pair of coordinates.

Two kinds are common. In a resistive screen, a press joins two conducting layers and the controller reads a voltage. A capacitive screen senses a finger, which conducts, through a change in capacitance. Most smartphones use capacitive screens, McGill University's Office for Science and Society noted in September 2025.

The BYU Design Review describes two more kinds. In a surface acoustic wave screen, a touch absorbs ultrasonic waves crossing the glass. In an infrared screen, a finger interrupts a grid of infrared light from LEDs around the edge.

Why does a finger change a screen's capacitance?

Capacitance is how much electric charge a pair of conductors stores for each volt between them. Its unit is the farad (F), one coulomb per volt, and it depends on the conductors' size and spacing and the material between them, a University of Texas physics text explains. The student meets capacitance in Class 12 Physics.

A farad is a huge unit. NIST, the US standards agency, lists the prefix pico as 10⁻¹², and touch sensing works in picofarads (pF).

A finger is a conductor joined to the body, so it changes the capacitance of any sensing line it comes near. E. A. Johnson's touch display patent sensed the operator's natural capacitance to earth, of the order of picofarads.

At CERN, a touch button of about 200 pF rose by about 10%, roughly 20 pF, when a finger came near, the CERN Courier reported in March 2010.

How does a resistive screen find where it is pressed?

A resistive screen stacks two layers. Illumin, a University of Southern California engineering magazine, describes a flexible transparent top layer over a rigid one, usually glass, both coated with a conductor, most often indium tin oxide. Tiny spacers keep a gap between them.

A small voltage is applied across the screen, horizontally and vertically. A press bends the top layer onto the bottom one, changing the voltages, and a processor calculates the location, Illumin explains.

This uses the voltage divider idea. Purdue University's physics lab notes show that along a uniform wire, the voltage across a length x equals the total voltage times x divided by the whole length. So the voltage at the contact point tells the controller how far along the layer it is.

A press needs force, not electricity, so a finger, a pencil or a glove all work, McGill's office notes. Scienceline, a New York University science site, reported in January 2012 that ordinary resistive screens handle one touch at a time.

How does a projected capacitive screen find one finger, or several?

A projected capacitive screen needs no press. Scienceline shows a grid of rows and columns of conducting lines, each thinner than a human hair, read by a separate chip. Illumin calls one set the driving lines, connected to a power source, and the other the sensing lines.

A US patent for a "multipoint touchscreen", granted in February 2010, explains how such a grid is read. Each crossing of a driving line and a sensing line is a node with its own capacitance.

The controller drives one line at a time and reads all the sensing lines together. A finger near a node draws away some charge, which changes the capacitance there.

Because every node gives its own reading, one scan maps the whole screen, and two fingers show up at two places. The patent's screen tracks several contact points at once: multi-touch.

A finger can also influence two or more electrodes at once, the patent notes, which allows interpolation, placing a touch between lines. It also describes finding the centre point, or centroid, of each touched area.

Why must the conducting layers let light through?

The sensing layers lie on top of the picture, so its light must pass through them. The conductor has to be transparent as well as able to carry a current.

The usual choice is indium tin oxide (ITO). The Royal Society of Chemistry says most indium goes into ITO, an important part of touch screens, flat-screen televisions and solar panels, because it conducts electricity, bonds strongly to glass and is transparent.

There is a trade-off. The US Department of Energy's Office of Science explained in a 2013 feature that ITO is transparent only in very thin layers, and thinning it reduces how well it conducts. CERN's early screens took another route: copper lines 80 micrometres (µm) wide and 80 µm apart, fine enough to be invisible.

Why do gloves, water drops and some styluses behave differently?

A capacitive screen needs something that conducts. McGill's office and Scienceline explain that ordinary gloves do not conduct electricity, so a gloved finger does not register. Gloves made for touchscreens get around this: their fingertips, McGill's office notes, are sewn with conductive thread.

Water causes the opposite problem. McGill's office points out that water conducts electricity, so water spread over a capacitive screen can act like many touches at once.

A stylus for a capacitive screen has to stand in for a fingertip. The BYU Design Review, a Brigham Young University publication, says these screens respond to a finger or a conductive stylus but not to non-conductive materials, so such a stylus must conduct where it touches. A resistive screen has no such limit.

How did touchscreens develop in the United Kingdom, Switzerland and the United States?

  • United Kingdom. E. A. Johnson of the Royal Radar Establishment in Malvern described a touch display in the journal Electronics Letters in October 1965, and Illumin credits him with the first finger-driven touchscreen. His patent, filed in the United Kingdom on 5 August 1965 and granted in the United States on 2 December 1969, describes touch-sensitive wires on a cathode ray tube, sensed by a change in capacitance or resistance, for amending flight plans in air traffic control.
  • Switzerland. At CERN, the particle physics laboratory in Geneva, Bent Stumpe proposed a capacitive touch screen in a note of 11 March 1972, and he and Frank Beck described it in a report of May 1973. When CERN's SPS accelerator started in 1976, its control room was fully equipped with touch screens, "apparently the first application" of the capacitive touch screen, the CERN Courier said.
  • United States. Oak Ridge National Laboratory (ORNL) says its physicist Sam Hurst pioneered resistive touchscreen technology. In 1971 he started Elographics to make the Elograph, which used two conductive layers to find a position along both axes. He later refined it for a transparent screen and showed a touchscreen at the 1982 World's Fair in Knoxville, Tennessee.

The two "first" claims differ: Illumin's is about the invention, and the CERN Courier's is about putting capacitive touch screens to use.

What do supporters and critics argue?

How long makers must supply spare parts for repairs, and for which parts, is debated.

  • Supporters of the rules. The European Commission, the European Union's executive, says ecodesign rules applying since 20 June 2025 require makers of smartphones and tablets sold in the EU to supply critical spare parts within 5 to 10 working days, for at least 7 years after a model stops being sold there. It projects that consumers will save €20 billion in 2030.
  • Cautious voices. Thirty industry bodies, including DIGITALEUROPE, an industry association, said in a joint statement on 25 July 2022 that displays and batteries are by far the most relevant parts for repair. They warned that an overly detailed list of parts that must be replaceable could harm reliability, asked for spare-part periods matched to real demand to avoid destroying unused parts, and asked for at least 24 months to adapt designs.

How does this work with real numbers?

Both examples use illustrative inputs.

Where is the press on a resistive screen?

Rearranged, the voltage-divider rule gives: distance from the 0 V edge = measured voltage ÷ total voltage × layer length.

  • Across: an illustrative layer 10 cm wide has 5 V across it, and the controller reads an illustrative 2 V where the layers touch. Distance = 2 ÷ 5 × 10 = 4 cm from the 0 V edge.
  • Down: the controller puts 5 V across the other direction, an illustrative 6 cm, and reads an illustrative 3.5 V. Distance = 3.5 ÷ 5 × 6 = 4.2 cm, so the touch is at (4 cm, 4.2 cm).

How many readings does a capacitive grid take each second?

  • Nodes: an illustrative screen has 15 driving lines and 30 sensing lines, so 15 × 30 = 450 crossing points.
  • Readings: if the controller reads every node an illustrative 120 times a second, that is 450 × 120 = 54,000 readings a second, about one every 18.5 microseconds.
  • Drive steps: driving one line at a time and reading all 30 sensing lines together takes 15 steps a scan, so 15 × 120 = 1,800 steps a second, each at most 1 ÷ 1,800 ≈ 0.00056 seconds.
  • Between lines: if a touch changes the reading at line 7 three times as much as at line 8 (illustrative), the weighted centre is (7 × 3 + 8 × 1) ÷ (3 + 1) = 7.25.

Where can the student go deeper in World 101?

This page follows one touch from the glass to a pair of numbers that software can act on. The World 101 subject Computing Fundamentals takes the wider view: how computers take in data from devices such as screens and keyboards, and how programs then decide what each tap should do.

Three related subjects go further, each from its own side. Electrical & Electronics Engineering covers circuits, signals and devices, including the voltage dividers and capacitors inside a touch controller. Materials Engineering explains how materials such as indium tin oxide are chosen and tested for a product. Product, Industrial & Interaction Design looks at how people use the screens, buttons and controls in front of them, and how designers make them easy to use.

Sources

  • R. Fitzpatrick, University of Texas at Austin, "Capacitance" and "Dielectrics", 14 July 2007.
  • NIST, Guide to the SI, chapter 4, updated 18 August 2025.
  • Purdue University, Physics 271L voltage divider notes, read 11 November 2026.
  • Illumin (University of Southern California), Q. Dang, 30 October 2018.
  • E. A. Johnson, "Touch display: a novel input/output device for computers", Electronics Letters, vol. 1, no. 8, October 1965.
  • Scienceline (New York University), A. T. McCann, 17 January 2012.
  • McGill University Office for Science and Society, E. Kellner, 26 September 2025.
  • The BYU Design Review, D. Conover, 16 March 2026.
  • US Patent 7,663,607, "Multipoint touchscreen", filed 6 May 2004, granted 16 February 2010.
  • Royal Society of Chemistry, periodic table: indium, read 11 November 2026.
  • US Department of Energy, Office of Science, P. Glynn, "Revolutionizing the Touch Screen?", 2013.
  • US Patent 3,482,241, "Touch displays", E. A. Johnson, UK filing 5 August 1965, granted 2 December 1969.
  • CERN Courier, B. Stumpe and C. Sutton, 31 March 2010 (note, 1972; report, 1973; SPS, 1976); CERN history page, read 11 November 2026.
  • Oak Ridge National Laboratory news, 30 June 2026 (Elographics, 1971; World's Fair, 1982).
  • European Commission, news of 20 June 2025 (savings in 2030); products page, read 11 November 2026.
  • DIGITALEUROPE and 29 other bodies, joint statement, 25 July 2022.

Common errors and misconceptions

  • Misconception: Every touchscreen senses pressure. Correct: Resistive screens need a press; capacitive screens sense the change in capacitance a conducting finger causes.
  • Misconception: A capacitive screen responds to any object. Correct: It responds to conductors such as a finger or a conductive stylus; ordinary gloves do not conduct, so they do not register.
  • Misconception: The sensing layer over a screen is plain glass. Correct: It carries thin conductors, usually indium tin oxide, that let the picture through.
  • Misconception: A grid can only place a touch exactly on one of its lines. Correct: A fingertip affects neighbouring lines, so the controller can interpolate a position between them.
  • Misconception: Touchscreens were invented for smartphones. Correct: Johnson's touch display dates to 1965, and CERN's SPS control room was fully equipped with touch screens by 1976.

Key takeaways

  • A touchscreen's controller turns an electrical change in thin, transparent layers into a position: how far across and how far down the screen the touch was.
  • A resistive screen joins two conducting layers when pressed, and the voltage at the contact point gives the position by the voltage-divider rule.
  • A projected capacitive screen drives one line of its grid at a time and reads the crossing lines; a conducting finger changes the capacitance at nearby nodes.
  • Because each node is read separately, a capacitive grid can follow several fingers at once and interpolate positions between its lines.
  • The conductors must let the picture through; indium tin oxide is the usual choice, but it stays transparent only in very thin layers that conduct less well.
  • Touch displays date from Johnson's 1965 work, CERN's capacitive screens and Hurst's resistive screens; how long makers must supply spare parts is debated.

Test yourself

Why does an ordinary glove not work on a capacitive screen?

Ordinary gloves do not conduct electricity, so the gloved finger cannot act as the conductor that changes the capacitance of the grid.

An illustrative resistive layer 10 cm wide has 5 V across it, and the controller reads 2 V. Where is the touch?

2 ÷ 5 × 10 = 4 cm from the 0 V edge.

How many readings a second does an illustrative grid of 15 by 30 lines need at 120 scans a second?

15 × 30 = 450 nodes, and 450 × 120 = 54,000 readings a second.

Why can a projected capacitive screen follow two fingers at once?

Each crossing of a driving line and a sensing line gives its own reading, so two touches show up as changes at two separate places.

Why is indium tin oxide used in touchscreens?

It conducts electricity, bonds strongly to glass and is transparent, so the picture can shine through the sensing layers.

How large was a finger's effect on a CERN touch button?

A finger raised the capacitance of a button of about 200 pF by about 10%, roughly 20 pF, the CERN Courier reported.

Go deeper in World 101: Computing Fundamentals

Write about it

Turn a question from this chapter into a paper.

The Writing Studio has a structure guide, a rubric and citation tools for 15 formats, from essays to research papers. A free account keeps up to five drafts. Learnacy Essential adds feedback from an AI writing coach and submission to The OYI Review.

Publication depends on review and is not guaranteed.